(978)686-6332 sales@nedc.com


Array of Connector Gaskets

Array of Connector Gaskets

EMI Gaskets play an important role in any electronic design that is attempting to shield EMI from their assembly. In our eyes, there are two different types of EMI Gaskets. There are environmental gaskets, and there are EMI Gaskets. However, some of the solutions below are able to serve both purposes simultaneously. The material below is mainly rubber based materials that are shielding EMI interference. 



Frequently, gasket manufacturers are being asked to certify to the MIL-DTL-83528. This is a widely used specification. These different electrically conductive rubbers really come down to two variables for the selection. There are the particle fillers, and there is the rubber content. Many combinations of these are available. For example, nickel graphite is able to come with EPDM, fluorosilicone, and silicone. 

The elastomer options really come down to a few variables which are toughness, temperature range, and fluid resistance. The elastomer essentially binds the electrically conductive particles into the molded/extruded shape to make it electrically conductive while also maintaining an elastic nature. Typically fluorosilicone is utilized for situations where fluid resistance is required. Silicone has always been the good general purpose option for EMI Gaskets. EPDM is usually utilized for outdoor applications that will not see temperature extremes nor fluid contact. Silicone Rubber for NEDC is easily the most popular through MIL-DTL-83528 Type B, however. 


FIller Particles Available: Cost($, $$, $$$, $$$$): Included In the MIL-DTL-83528
Nickel Graphite  $ No
Pure Silver $$$$ Yes(Type E, Type F, Type H, Type J)
Silver Aluminum $$$ Yes(Type B, Type D)
Silver Nickel $$ Yes(Type L)
Silver Glass $$ Yes(Type M)
Silver Copper $$$ Yes(Type A, Type C, Type K)
Nickel Aluminum $$ No
Passivated Silver Aluminum  $$$ Yes(Type D)

emi gaskets

emi gaskets assortment

Cost Sensitive Solutions for EMI Gaskets

It is good to note that the electrically conductive rubber also have some cost sensitive solutions that may serve the same purpose. Many design engineers will utilize nickel/graphite filler instead of costly silver based fillers. It has been shown that nickel/graphite can have similar performance in some applications for shielding effectiveness. Although, testing should be key to making sure the solution you are selecting will match the performance requirements. 

These gasketing materials are able to be fabricated into finished gaskets through waterjet cutting, or die cutting. However, bonding of gaskets through vulcanizing cord stock. Cord stock is produced through extrusion machines. 

Whats Popular when it comes to EMI Solutions?

One of the things we mention a lot on this website is it is important to choose materials that converters/fabricators are familiar with. The reason for this, many converters should be able to get the material quickly, and be familiar with it. In addition, many companies who manufacture electrically conductive gasket materials should have them too. 

-Silicone Rubber Silver Aluminum

-Fluorosilicone Rubber Silver Aluminum

-Fluorosilicone Rubber Passivated Silver Aluminum

-Silicone Rubber Nickel Graphite


The MIL-DTL-83528 specification utilizes so-called “slash” sheets to make it easier for design engineers to call out different types of normally custom configurations of these materials. For example M83528/004D001 calls out a Type D connector gasket with a custom configuration of dimensions. There are other slash sheets for flange gaskets, washers, and other configurations. 

The different configurations are listed below in the table:

Slash Sheet Configuration
M83528/001 Solid O-Strip Channel Extrusion
M83528/002 Molded O-Ring
M83528/003 Solid D-Strip Channel Extrusion
M83528/004 Connector Gaskets(.032’’ thickness)
M83528/005 Molded O-Ring
M83528/006 Molded D-Ring
M83528/007 Hollow D-Strip Channel Extrusion
M83528/008 Hollow P-Strip Channel Extrusion
M83528/009 Solid Rectangular Strip Extrusion
M83528/010 U-Channel Strip Extrusion
M83528/011 Hollow O-Strip Channel Extrusion
M83528/012 Circular Washer Die-Cut
M83528/013 Molded Waveguide Parts

It is good to keep in mind as well that there are many other extruded options available for EMI Gasketing, some custom ones may include “bunny ears”, or “cowboys hats”.

Modified EMI Rubber Gaskets

There are a number of different options when it comes to modifying a EMI Rubber gasket material into something slightly different than what they normally are available in.

For example, there are soft durometer gaskets. Some EMI Rubber materials are available in 45 durometer. 

Lamination/Converting of EMI Gaskets:

All of the different materials above are either die-cut or waterjet-cut into custom shape gaskets. When these gaskets are fabricated there are times when an electrically conductive adhesive tape may be required on the back. NEDC is a 3M converter, so we utilize electrically conductive tape products such as 3M 9713(acrylic adhesive), and 3M 9719(silicone adhesive). These tapes are laminated to the material. 

Oversized EMI Gasketing Options

One thing to keep in mind when designing an EMI Gasket is many times electrically conductive rubber options are molded sheets. For this reason, beyond 24’’ in any one direction can be difficult to fabricate out of a single piece of EMI material. In these cases, it may be a good idea to specify how the gasket can be put together. There are electrically conductive adhesives available for fabricating bigger gasket shapes by vulcanizing separate pieces together and then cutting a complete shape. 


For more information on electrically conductive gasketing products, please contact our sales department.

Popular Blog Post
Previous Posts


We are an authorized 3M Converter at NEDC. As a result, we work with many...

read more


NEDC has been die-cutting thermal pads since its inception in 1982. One...

read more


At NEDC, we offer an incredibly wide range of materials. High performing...

read more

All of the information presented above is believed to be factual and accurate; however, NEDC is not liable for any design or application utilizing this information.

New England Die Cutting

Popular Blog Posts


NEDC has been die-cutting thermal pads since its inception in 1982. One of the more popular products Sil-Pad 900S by Henkel’s Bergquist. It is one of the most commonly die-cut materials NEDC converts. This product is part of the Sil-Pad family, featuring great thermal...

©New England Die Cutting 2022

快乐飞艇大小玩法 秒速飞艇开奖记录 秒速赛车官网开奖 秒速赛车开奖历史 秒速赛车在线预测 SG赛车计划网 秒速赛车分析 极速赛车开奖号码记录 澳洲幸运8网上投注 极速赛车开奖走势图